Water prices have recently increased significantly, by an average of about 20%. At the same time, the amount of drinking water is constantly decreasing, which is why various actions should be taken to save water and reduce its consumption. A flow regulator placed in the faucet will work perfectly here. It is worth learning more about it.
Check out the flow regulators at the Onninen wholesaler
What is a water regulator and how does it work?
The water flow regulator is a product that is an element of the faucet. It is located at the end of the spout. Its operation is very simple. It aerates the water flow, which reduces its consumption by up to 50%. The element is really small. At the same time, it has the form of a special tip made of a strainer with small holes. This construction makes the water flow much smaller, which of course translates into lower water consumption. The water flow regulator fits both kitchen faucets and bathroom or even shower faucets.
Therefore, it is worth placing it not only in the kitchen, but also in the bathroom, to feel the big savings. It is worth noting that the water flow is really big, so you do not feel at all that there is less water. Importantly, this small investment translates into really big savings. When choosing, it is worth paying attention to the type of thread. It should be made of strong materials. For example, silicone aerators are available, but also metal and plastic ones. We also distinguish aerating aerators and those creating a needle stream. The first one creates negative pressure in the water flow, which then flows out of a fine mesh.
The vacuum causes air to be sucked in through small holes, which makes it seem like there is more water flowing out. There is also an aerator that creates a needle stream. The water flow can have different directions in this case, thanks to the sieve. You don't have to worry about water splashing. An interesting choice is also a dual-function aerator, which has two water stream functions, and switching between them is very simple and intuitive. The model with a ball joint allows you to set the water depending on your needs.
Savings from using a flow regulator
An aerator should be placed in both kitchen and bathroom faucets. Its functions can save a lot. As a result, water consumption can be reduced by up to 50%. However, it is worth taking a closer look at the savings that result from its use. By choosing very cheap aerators, we reduce water consumption by 15%, while the latest models reduce water flow by up to 60%. Kitchen faucets with aerators provide water flow savings of up to 5 l/minute.
In comparison, a kitchen tap that is not equipped with an aerator uses about 13l/minute. In addition to significant savings in water consumption, energy bills are reduced, because less water for heating actually reduces the costs of consumption, e.g. gas or electricity. The amount of sewage is also reduced. An aerator should be found not only in the kitchen, but also in the bathroom. Bathroom taps use less cold water thanks to the flow regulator. As a result, savings can be as much as 60%.
How to care for the flow regulator in faucets?
In order to be able to use the stream regulator for a long time, it is worth taking care of it and performing regular inspections. Contrary to appearances, keeping it clean is not difficult at all. It should be cleaned of dirt that has settled. It is worth remembering that accumulated scale can block the operation of the aerator, therefore it is necessary to clean the sieve that is located inside.
For example, you can use a toothbrush for this purpose. It is best to soak it in water with vinegar and then remove the scale. You can also take it apart and clean each element one by one. Of course, you also need to pay attention to the material it is made of. For example, a silicone aerator is the easiest to keep clean. If it is made of metal, you often need to use a descaling agent.
Flow regulators at the Onninen wholesaler
It is worth choosing the Ferro M24x1 PCH2 flow regulator . This is a really high-quality product at a low price. It is made of metal. For even greater efficiency, it has a strong seal that prevents leaks.
The Geberit M18.5x1, 5.0 l/min, rotatable 243.635.00.1 jet regulator is also worth mentioning. It impresses with its practical values and extraordinary durability. The silicone used means that it will last for a really long time. It also allows you to reduce water consumption by over 50%.
A good choice may be the CLAGE CSP6i jet regulator with a chrome-plated sleeve M22i (for fittings with an external thread on the spout) 00460. It will work with almost any fitting that has an external thread on the spout. It is equipped with a chrome-plated sleeve that is resistant to corrosion.