Preparing an appropriate hydraulic system is necessary to maintain safety, but also to reduce wear and tear costs. The key role here is played by the stubs that enable the supply and discharge of the medium. It is worth learning more about them and learning about the advantages of using them.
Check the spigots at the Onninen wholesaler
Advantages and functions of connectors in gas installations
The gas installation must be 100% tight and there cannot be any leaks, even the smallest ones, because then there is a risk of explosion. It is necessary to use spigots. Undoubtedly, stub pipes are an extremely important assembly element. LPG moves between them in a gaseous state. We are talking here about the volatile phase. A flange stub , which is intended for connecting pipes, works very well. It is best to choose a model made of steel, which is resistant to mechanical damage and at the same time ensures maximum tightness.
The use of a threaded stub is necessary in places where threaded elements for transmitting liquids are connected. Here we recommend installation connectors made of galvanized steel. Such a threaded connector may have a diameter of about 0.5". It is also used in heating installations. It allows for trouble-free and easy connection of pipes. You should know that the gas installation in the house can be screwed, in which case a threaded connector is used. It is also recommended a quick flange connector that will seal the gas installation. However, you should pay attention to the pressure at which the gas flows. Most often, this type of gas gate valves is suitable for installations where the gas pressure does not exceed 16 bar.
At the same time, they can work on their own even when the temperature is negative, but it cannot be lower than minus 20 degrees. By using a reduction on the hose, you gain greater safety, but also the efficiency of the entire installation. The gas connector should have a properly selected tip. The threaded connector is intended for a steel pipe. It allows you to prepare a strong cable, even in technological installations. Indeed, it is perfect for connecting threaded components for transmitting liquids. We recommend the threaded model, made of stainless steel, which is additionally galvanized. The use of a pipe stub in gas installations is also possible.
Application and installation of a flange stub in hydraulics
The use of the flange stub is really wide. The flange model can also be used in water installations. Installing the spigot is really simple. All you need to do is put a gasket on the hydraulic connector and then insert it through the drilled hole. This can take place already in the tank. Remember that if there is a slight problem with the transmission, you can use a rubber hammer and gently knock in the stub, and if it sticks out, you need to use a gasket and finally a nut.
Connecting the stub pipe requires preparing a hole in advance. Here you can use a hole saw. The diameter of the hole should correspond to the diameter of the spigot. Make sure the unit of measurement is correct, so use either inches or centimeters. Finally, tighten the connector and clean the tank of any impurities.
Connectors at the Onninen wholesaler
A product worthy of attention is the Simet KD12 spacer stub . It is intended for boxes connected in series. Thanks to it, you can achieve an even larger spacing of the cans. The connection is then much more durable. It is worth noting that such models are very easy to install. It can be used when accessories with a spacing of more than 71 mm are mounted on the boxes. This is a non-frame model. The operating temperature of this type of product is over 960 degrees Celsius.
For the bathroom, you can choose the Geberit connection stub for the drain for standing toilet bowls D120 . This model is also characterized by extraordinary durability and resistance to damage. It is made of plastic. Thanks to this, it is not susceptible to corrosion in any way. The ergonomic design makes its assembly and disassembly really quick. It is intended for drainage into standing bowls. It will indeed work in many different models. It is characterized by great universality.
The Bohamet FF DN100x200, PN10, GJL double-flange connector - gray cast iron - will also work well for water supply installations. It is also used in drinking water installations. It is made of cast iron. It is an extremely strong material, resistant even to large overloads or pressure changes. It is a stainless steel model that, despite its low price, can actually be used for many years. We must also mention that its weight is over 12 kg, but despite this, assembly is not time-consuming at all.